新闻资讯

公司与国内知名房产单位以及各大建筑单位建立了良好的合作关系,是目前国内专业的金属、PVC落水系统解决专家

  • 卫生间安装下水管需要考虑哪些因素?
  • 本站编辑:杭州得裕建材有限公司发布日期:2018-06-21 16:53 浏览次数:

刷古铜方管_副本

卫生间下水管安装方法
Installation method of lower water pipe in toilet
1、卫生间下水道安装之前要进行对应的检查,首先室内一定会有对应的进水总阀,其次要检查安装卫生间下水管道所需的水管及连接配件是否有破损、砂眼以及裂纹等现象,发现问题要及时更换水管的有关部件。
1, toilet sewer installation should be checked before the installation of the corresponding, the first indoor water must have the corresponding total valve, secondly to check the installation of the toilet sewer pipe and connection parts are damaged, sand and cracks and other phenomena, found that the problem should be more timely and more relevant parts of the water pipe.
2、接下来要在墙面对应的管道位置,同时要考虑到墙砖贴好后的尺寸,也就是说要预先考虑墙砖的厚度。
2, next to the corresponding pipe position in the wall, at the same time, we should take into account the size of the wall tiles, that is to say, we should consider the thickness of the brick in advance.
3、连接卫生间下水道的配件,将它们安装在对应的墙体内、地面下等位置,注意这个过程中尽可能少用或不用连接配件,主要是为了减少渗漏隐患点。
3, connect the accessories of the toilet sewer, install them in the corresponding wall, the ground lower position, attention to the process as little as possible or not connected parts, mainly in order to reduce the leakage potential.
4、坐便器的进水出口尽量安置在能被坐便器挡住视线的地方。连体坐便器要根据型号来确定出水口的位置,一般要留在马桶下水口正中左方200mm处。
4, the water outlet of the toilet can be placed in the place where the toilet can be blocked. The conjoined toilet should be determined according to the type of the outlet. Generally, it should stay at the 200mm of the left side of the toilet.
5、淋浴混水阀的左右位置正确,且装在浴缸中间(先确定浴缸尺寸),高度为浴缸上中150-200mm,所需的按摩浴缸根据型号进行出水口预留。混水阀孔距一般保持在(暗装)150mm,(明装)100mm,连杆式淋浴器要根据房高和业主个人需要来确定出水口位置。
5, the right and left position of the shower valve is right and installed in the middle of the bathtub (first determining the size of the bathtub), the height is 150-200mm on the bathtub, and the required massage bathtub is reserved according to the type of the outlet. The distance between the mixing valves is generally maintained at (dark) 150mm, and the connecting rod shower should be determined according to the height of the housing and the individual needs of the owner. The location of the outlet is determined by the 100mm.
6、水路改造完毕要做管道压力实验,实验压力不应该小于0.6MPa。时间为20-30分钟。
6. The pipeline pressure test should be done after the transformation of the waterway, and the experimental pressure should not be less than 0.6MPa. The time is 20-30 minutes.
7、墙面上给水预留口(弯头)的高度要适当,既要方便维修,又要尽可能少让软管暴露在外,并且不另加接软管,给人以简洁、美观的视觉。对下方没有柜子的立柱盆一类的洁具,预留口高度,一般应设在地面上500-600mm左右。立柱盆下水口应设置在立柱底部中心或立柱背后,尽可能用立柱遮挡。壁挂式洗脸盆(无立柱、无柜子)的排水管一定要采用从墙面引出弯头的横排方式设置下水管(即下水管入墙)。
7. The height of the water supply reservation (elbow) on the wall should be appropriate, not only to be convenient for maintenance, but also to expose the hose as little as possible, and not to be added to the hose, so as to give people a simple and beautiful vision. For the type of sanitary ware below the cabinet without a cabinet, the height of the mouth should be set at about 500-600mm on the ground. The outlet of the column basin should be placed behind the bottom of the column or behind the column. Wall drain type washbasins (no columns, no cabinets) must drain the water pipes from the wall and draw the elbow.

杭州得裕建材有限公司

地 址:杭州市余杭区余杭镇义桥工业园区

手 机:13758137262 ( 乔经理 )

座 机:0571-56017206

传 真:0571-85853340